How do I reset my TaoTronics Bluetooth Soundbar?

How do I reset my TaoTronics Bluetooth Soundbar? 

How Do I Reset My Taotronics Bluetooth Speaker? A “factory reset” can be performed by pressing the multi-function button for approximately 5 seconds until the red LED flashes.

How do I reset my TaoTronics speaker? 

In order to perform a “factory reset“, simply press the multi function button for approx 5 seconds until the red LED flashes once. The speaker is now reset and can be paired with a new device. Do not forget to remove the TaoTronics TT-SK09 speaker from your Bluetooth device list on your mobile device.

Why is my Bluetooth Soundbar not working? 

Bluetooth pairing was made to be simple and easy. Put both devices in pairing mode, confirm a PIN if necessary, and that’s it. If the pairing is not working, it is typically because it is being performed incorrectly, or the device may need to be reset, updated, or may not be compatible with the soundbar.

How do I setup my TaoTronics wireless soundbar? 

How to Set up the TaoTronics Sound Bar
  1. Connect to a 5V / 1A power source.
  2. Plug in the 3.5mm audio cable into the audio output of your device. Connect the green jack to the audio and pink to the microphone output.
  3. Make sure the music is at audile level and tune the volume through the Volume Knob.

How do I reset my TaoTronics Bluetooth Soundbar? – Related Questions

How do I connect my TaoTronics to my TV?

We recommend TaoTronics TT-BA01 as it offers a quick way to connect your wireless headphones to your TV. If your TV has Bluetooth support, put your headset on pairing mode. You’ll notice a blue blinking dot next to the Bluetooth icon to show that it is in pairing mode.

How do you put a TaoTronics speaker in pairing mode?

Read the safety instructions!
  1. Turn the TaoTronics Mini (TT-SK03) speaker on by pressing the Power button for approx 2 seconds and ensure that the battery fully charged.
  2. Once switched on, the loudspeaker is automatically set to the pairing mode and can be paired with other Bluetooth enabled devices.

How do I connect my Taotronics soundbar to my Roku?

To hook up your Roku TV to a Soundbar with an HDMI cable, follow these steps:
  1. Purchase all the necessary equipment.
  2. Run the HDMI cable from the Roku TV to the Soundbar.
  3. Adjust your TV settings.
  4. Purchase all the necessary equipment.
  5. Connect the Bluetooth receiver to your TV’s RCA output.
  6. Pair the two devices via Bluetooth.

How do I turn up the volume on my Taotronics?

Volume +: Tap once the multifunction touch control on the right earbud. Volume -: Tap once the multifunction touch control on the left earbud. Play next track: Tap the multifunction touch control on the right earbud three times. Play previous track: Tap the multifunction touch control on the left earbud three times.

Why is my soundbar making a buzzing sound?

Connection Problem

If any wire is loosely connected to your soundbar, it can create a buzzing or humming sound.

How do you fix a buzzing sound bar?

Sound Bar Buzzing or Humming
  1. Power cycle the sound bar.
  2. Verify the cables are properly connected.
  3. If you have other cords- try connecting the sound bar using those ‘other’ cords.
  4. Try a ‘Factory Reset’ on the sound bar.
  5. See if the issue happens to the TV when when the sound bar is disconnected.

Why does my soundbar keep making static noise?

When you hear static coming from your soundbar, it could be from a bad signal from the TV or a poor connection. Did you know that it could also be caused by your phone? Mobile devices, like phones and tablets, can cause interference when placed near the soundbar, which will in turn cause static.

How do you fix a buzzing speaker?

How to stop speaker from buzzing sound
  1. Troubleshoot the hardware problem.
  2. Break the electrical ground loop.
  3. Avoid frequency interference.
  4. Update your audio driver.
  5. Configure audio settings in computer.

Why is my speaker making a buzzing noise?

There are multiple reasons why your speakers could be buzzing. The most common reason is when the volume or bass has been turned up too high and it’s putting a lot of pressure on the speaker. This can cause a sound loop to form, which will make your speakers buzz.

What causes humming noise in speakers?

Though some noise is inherent in the audio signal (tape hiss, amp gain, etc.), speaker hum and hiss generally come from poor wiring, ground loops or other electromagnetic interferences (AC line hum; RF interference, and USB and PC noise). To rid of the noise, we must rid of the interference.

Why is my speaker making a crackling sound?

Speaker crackling is almost always caused by a connection problem. Someplace between your amplifier and your speaker driver, there’s a bad wire which is causing the driver to move abruptly, causing interference.

What’s crackling mean?

1 ˈkra-​k(ə-​)liŋ : a series of small sharp cracking noises the crackling of frozen snow as we walk. 2 ˈkra-​klən , -​kliŋ a : the crisp residue left after the rendering of lard from pig fat or the frying or roasting of pig skin Want to know how to get perfect crisp crackling on roast pork? —

Why do my speakers sound distorted?

Higher volume means asking the amplifier for more power. If it is unable to provide enough, your speakers will distort. If speakers are a low build quality, they can easily be damaged at high volumes, regardless of the amount of power from the amplifier. As volume increases, the drivers extend further and faster.

How can you tell a speaker is blown?

The most common aural indication of a blown speaker is an unpleasant buzzing or scratching sound, by itself or roughly at the pitch of the note the speaker is attempting to reproduce. Or there could be no sound at all.

Can a blown speaker fix itself?

Of course, the first question is always “can you fix a blown speaker?” Yes, you can, but it’s rarely recommended to do-it-yourself. DIY speaker fixing is usually quick and dirty and only done on speakers you don’t really care about having perfect quality, such as in your 20 year old car.

How do you diagnose speaker problems?

Use a multimeter to check the ohms between the positive and negative leads to the speaker. Something between 1 and 16 ohms should be be the resistance of a working speaker. If its 0 or infinity there are likely problems and the speaker may be blown.Aug 20, 2018

What happens when a speaker is blown?

The term “blown” is used as a blanket term to describe a speaker that is not working right. It can mean that your speaker is reproducing scratchy signal at a lower volume, or no sound is passing through the speaker.