Why is my DIRECTV not showing a picture?

Why is my DIRECTV not showing a picture? 

If you’re seeing a black, blue, or gray screen, or a No Signal message without the DIRECTV logo, try these quick fixes. Turn your TV and receiver off and back on. On a Genie remote, press and hold the ENTER button for three seconds to cycle through TV inputs (component, HDMI, etc.) until you see a picture.

Why does my DIRECTV keep going black? 

If you change the DirecTV input into the TV from an HDMI ARC port to a non-ARC HDMI port it should solve the issue.

How do I reboot my DIRECTV receiver? 

Unplug your receiver
  1. Unplug your receiver’s power cord from the electrical outlet, wait 15 seconds, and plug it back in.
  2. Press the Power button on the front panel of your receiver. Wait for your receiver to reboot.

Why did my DIRECTV stop working? 

Your DIRECTV connection might not be working due to the following reasons; Faulty Power supply of the receiver, malfunctioned satellite receiver, broken cables, improper connections or loose contact of the cables in use.

Why is my DIRECTV not showing a picture? – Related Questions

What input should TV be on for DIRECTV?

Plug one end of the cable into the HDMI port on the back of your receiver. Plug the other end of the cable into the HDMI port on your TV. Make sure you have selected the correct TV input source (example HDMI 1, HDMI 2). Set your TV resolution to 1080i or 720p.

Why is my TV saying no signal DIRECTV?

Solution 1: Check that your TV is set on the right input

Power your TV and receiver off and back on. 2. Ensuring that the TV is on, slowly go through the available inputs, pausing briefly at each until a DIRECTV picture returns.

How do I reset my DIRECTV Genie box?

How to reset your DIRECTV Genie, Genie 2, or Genie Mini
  1. Press the reset button (it’s the red one behind the access card door or on the side of the receiver. Wait for it to reboot.
  2. Unplug your receiver, wait 15 seconds, then plug it back in. Now press Power and wait for the receiver to start up.

What happens if I reset my DIRECTV receiver?

This erases all your recordings, all your settings, and puts your receiver or DVR in the state it was when you got it. We recommend this option before sending a defective or unwanted device back to DIRECTV.

How do I reset my satellite receiver?

To reset your receiver:
  1. Unplug the receiver’s power cord from the back of the receiver or from the wall outlet.
  2. Leave unplugged for 30 seconds and plug back in.
  3. The receiver should boot up properly in less than 90 seconds.

How do I factory reset my genie?

Press and HOLD the ON button for 13 seconds. A series of lights should flash. Your unit should now have a new name consisting of a series of numbers and letters.

How do I reset my genie?

Press down the square button for 3-5 seconds.

Keep holding the button until the circular LED is lit up. The oblong LED adjacent to the circular LED will then flash purple. This puts your opener into Programming Mode, which allows you to reset the device. The positions of your buttons may differ in certain Genie models.

How do I refresh my DIRECTV box?

To refresh:
  1. Go to myAT&T account overview and select My DIRECTV.
  2. Choose Manage Package.
  3. Scroll to Manage receivers and elect Refresh receiver.
  4. Your DIRECTV service may be interrupted for a few minutes during the refresh process.

How do I reconnect my mini genie?

Reconnect your Genie Mini receiver
  1. Press MENU on your Genie remote.
  2. Select Settings > Whole-Home > Manage Clients > Add Clients.
  3. Write down the PIN displayed on the screen.
  4. Return to the TV where you connected the Genie Mini.
  5. Use the remote to select Continue and enter the PIN when prompted.
  6. Select Add a New Location.

Why is my genie mini not working?

Make sure the HDMI connection to the TV is secure. Check that the TV input selection. Try changing the channels. Press and hold the red reset button located near the access card to reboot the system.

How do I connect my mini genie to my TV?

Connect your Wireless Genie Mini to a TV

Use an HDMI cable (recommended) for high-definition (HD) video and Dolby® Digital audio: Plug one end of the cable into the HDMI port on the back of your Wireless Genie Mini. Then, plug the other end into the HDMI port on the back of your TV.

How do I reset my DIRECTV Genie mini remote?

If that didn’t help, try resetting the remote to its default factory settings:
  1. Press and hold MUTE and SELECT together until the light flashes three times.
  2. Press 9, 8, 1 and SELECT. The remote flashes four times and should now reset.

Where is the reset button on my directv remote?

To reset DIRECTV remotes to their default factory settings, press and hold the MUTE and SELECT buttons until the remote’s light flashes three times. Then, enter 981 and press SELECT. The remote will flash four times to let you know it has been reset.

How do I resync my directv remote to my receiver?

Press and hold MUTE and SELECT until the light on the remote flashes twice. Then press 9 6 1 and press the CHANNEL UP button. Enter the last six digits of your receiver ID and press SELECT. (This is on a green sticker on the receiver or you can get it from your “My Equipment” page at DIRECTV.com.

How do you reset a remote control?

For Android TVs released in 2015 or later, symptoms may improve by updating the software of the remote control.

Reset the remote control.

  1. Open the battery compartment cover and remove the batteries.
  2. Press and hold the Power button for three seconds.
  3. Insert the batteries again and close the battery compartment cover.

Why won’t my DIRECTV remote change the channel?

If your remote is not responding, changing channels or adjusting the volume, make sure you have direct line of sight to the receiver.. Next, make sure your remote is set to control your DIRECTV receiver: At the top of the remote, slide the mode switch all the way to the left to the DIRECTV symbol.